TL MR3220 v2.1 i ZTE MF823 nie chcą współpracować

Witam, mam problem z udostępnieniem internetu dostarczanego przez ww. modem, podłączony do routera poprzez aktywny hub z własnym zasilaniem. Modem pojawia się jako zidentyfikowany, łączy się automatycznie z siecią (tak jest skonfigurowany) i na tym koniec. Strona modemu (192.168.0.1), kiedy jest podpięty pod router, przestaje być widoczna (router ma zmienione IP). Modem bez problemu działa podłączony do komputera.

Większość (chyba) opcji konfiguracyjnych, które mogą mieć związek z problemem jest na poniższych screenach:















Michał

Zmień adres IP routera na 10.0.0.1 i spróbuj wtedy podłączyć modem USB.

Niestety, bez zmian.

Klikając connect też nic się nie pojawia na WAN-ie? Zrób tam Connect Automaticlly w konfiguracji 3G/4G

Nic się tam nie pojawia, u góry pisze, że ustawienia WAN są niedostępne, gdy wybrane jest 3G/4G jako sposób podłączenia do internetu. Jeżeli przełączę na inne źródło (np. WAN only, albo WAN preferred) to również w wypadku ustawiania na DHCP nic tam nie wykrywa. Mogę zmienić na Static i wpisać ręcznie, ale domyślnie wszystkie adresy są na 0.0.0.0.

Tak chodziło mi o 3G/4G w tej konfiguracji to o jest WAN-em tego routera :slight_smile:
Do samej usługi nie masz żadnych loginów ani haseł? Daj jeszcze obrazek z logów routera.

Nie ma loginów o ile wiem - to jest internet z karty sim do połączeń głosowych w promocji "30 dni internetu LTE za darmo", pod laptopem (Win 8 ) oraz na desktopie (Linux) modem działa bez problemu, nie wymaga wprowadzania hasła ani nazwy użytkownika. Przesyłam screeny:
WAN:

Włożenie modemu:

Kilka chwil po włożeniu modemu:

Wyjęcie modemu:

EDIT:
Ja się na tym totalnie nie znam, ale jak tak patrzę na logi, to kurka, wydaje mi się, że przynajmniej sprzętowo wszystko jest ok. Modem jest rozpoznawany, router go widzi, ładuje sterowniki, włącza...

Nic mi więcej do głowy nie przychodzi, sama karat chyba PIN-u nie posiada bo wcześniej na komputerze pokazywałeś że łączy się bez niego. Zainstalował bym jeszcze Gargoyle i spróbował z alternatywnym oprogramowaniem. Nie posiadam takiego zestawu u siebie aby zweryfikować na 100%.
http://eko.one.pl/?p=openwrt-modemygsm#ztemf823
http://eko.one.pl/forum/viewtopic.php?pid=92753#p92753

Zainstalowałem Gargoyle (najpierw w wersji oryginalnej, potem z eko.one.pl, która pozwala wybierać interfejs WAN). Brak opcji usb0 w wyborze interfejsu WAN, zalogowałem się na modem i takie informacje udało mi się uzyskać:
nie ma jak widać interfejsu usb0 w ogóle.

Info w ifconfig -a :

root@Gargoyle:~# ifconfig -a
br-lan    Link encap:Ethernet  HWaddr A0:F3:C1:C3:B3:E5
          inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:630 errors:0 dropped:39 overruns:0 frame:0
          TX packets:248 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:58344 (56.9 KiB)  TX bytes:34031 (33.2 KiB)
eth0      Link encap:Ethernet  HWaddr A0:F3:C1:C3:B3:E5
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:634 errors:0 dropped:4 overruns:0 frame:0
          TX packets:248 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:67528 (65.9 KiB)  TX bytes:34031 (33.2 KiB)
          Interrupt:5
eth1      Link encap:Ethernet  HWaddr A0:F3:C1:C3:B3:E7
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:4
imq0      Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
          NOARP  MTU:16000  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:11000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
imq1      Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
          NOARP  MTU:16000  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:11000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:3168 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3168 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:190416 (185.9 KiB)  TX bytes:190416 (185.9 KiB)
wlan0     Link encap:Ethernet  HWaddr A0:F3:C1:C3:B3:E6
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:110 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:21343 (20.8 KiB)

Info w /proc/bus/usb/devices :

root@Gargoyle:~# cat /proc/bus/usb/devices
T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480  MxCh= 1
B:  Alloc=  0/800 us ( 0%), #Int=  1, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev= 3.03
S:  Manufacturer=Linux 3.3.8 ehci_hcd
S:  Product=Generic Platform EHCI Controller
S:  SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 4
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1a40 ProdID=0101 Rev= 1.11
S:  Product=USB 2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=256ms
T:  Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#=  5 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=19d2 ProdID=1403 Rev=f0.70
S:  Manufacturer=ZTE,Incorporated
S:  Product=ZTE WCDMA Technologies MSM
S:  SerialNumber=MF8230ZTED000000
C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=03
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=ff Driver=(none)
E:  Ad=82(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
T:  Bus=01 Lev=02 Prnt=02 Port=02 Cnt=02 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0951 ProdID=1603 Rev= 2.00
S:  Manufacturer=Kingston
S:  Product=DataTraveler 2.0
S:  SerialNumber=89900000000000006CB02AE6
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Info w /etc/config/network :

root@Gargoyle:~# cat /etc/config/network
config interface 'loopback'
        option ifname 'lo'
        option proto 'static'
        option ipaddr '127.0.0.1'
        option netmask '255.0.0.0'
config interface 'lan'
        option ifname 'eth0'
        option type 'bridge'
        option proto 'static'
        option ipaddr '192.168.1.1'
        option netmask '255.255.255.0'
config interface 'wan'
        option ifname 'eth1'
        option proto 'dhcp'
config switch
        option name 'eth0'
        option reset '1'
        option enable_vlan '1'
config switch_vlan
        option device 'eth0'
        option vlan '1'
        option ports '0 1 2 3 4'

EDIT: może jeszcze wkleję, jak modem jest rozpoznawany pod moim linuksem:

[18038.018988] hub 1-0:1.0: state 7 ports 10 chg 0000 evt 0400
[18038.018998] ehci-pci 0000:00:02.1: GetStatus port:10 status 001803 0  ACK POWER sig=j CSC CONNECT
[18038.019044] hub 1-0:1.0: port 10, status 0501, change 0001, 480 Mb/s
[18038.136762] hub 1-0:1.0: debounce: port 10: total 100ms stable 100ms status 0x501
[18038.190338] ehci-pci 0000:00:02.1: port 10 reset complete, port enabled
[18038.190343] ehci-pci 0000:00:02.1: GetStatus port:10 status 001005 0  ACK POWER sig=se0 PE CONNECT
[18038.243546] usb 1-10: new high-speed USB device number 18 using ehci-pci
[18038.297153] ehci-pci 0000:00:02.1: port 10 reset complete, port enabled
[18038.297158] ehci-pci 0000:00:02.1: GetStatus port:10 status 001005 0  ACK POWER sig=se0 PE CONNECT
[18038.393989] usb 1-10: default language 0x0409
[18038.394489] usb 1-10: udev 18, busnum 1, minor = 17
[18038.394491] usb 1-10: New USB device found, idVendor=19d2, idProduct=1225
[18038.394493] usb 1-10: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[18038.394495] usb 1-10: Product: ZTE WCDMA Technologies MSM
[18038.394497] usb 1-10: Manufacturer: ZTE,Incorporated
[18038.394498] usb 1-10: SerialNumber: MF8230ZTED010000
[18038.394586] usb 1-10: usb_probe_device
[18038.394588] usb 1-10: configuration #1 chosen from 1 choice
[18038.411528] usb 1-10: adding 1-10:1.0 (config #1, interface 0)
[18038.411776] usb-storage 1-10:1.0: usb_probe_interface
[18038.411780] usb-storage 1-10:1.0: usb_probe_interface - got id
[18038.411782] usb-storage 1-10:1.0: USB Mass Storage device detected
[18038.411850] scsi16 : usb-storage 1-10:1.0
[18038.937942] usb-storage 1-10:1.0: disconnect by usbfs
[18044.016851] hub 1-0:1.0: state 7 ports 10 chg 0000 evt 0400
[18044.016861] ehci-pci 0000:00:02.1: GetStatus port:10 status 001002 0  ACK POWER sig=se0 CSC
[18044.016911] hub 1-0:1.0: port 10, status 0100, change 0001, 12 Mb/s
[18044.016915] usb 1-10: USB disconnect, device number 18
[18044.016917] usb 1-10: unregistering device
[18044.016920] usb 1-10: unregistering interface 1-10:1.0
[18044.016974] usb 1-10: usb_disable_device nuking all URBs
[18044.136718] hub 1-0:1.0: debounce: port 10: total 100ms stable 100ms status 0x100
[18044.196915] hub 1-0:1.0: state 7 ports 10 chg 0000 evt 0400
[18044.196923] ehci-pci 0000:00:02.1: GetStatus port:10 status 001803 0  ACK POWER sig=j CSC CONNECT
[18044.196967] hub 1-0:1.0: port 10, status 0501, change 0001, 480 Mb/s
[18044.316910] hub 1-0:1.0: debounce: port 10: total 100ms stable 100ms status 0x501
[18044.370537] ehci-pci 0000:00:02.1: port 10 reset complete, port enabled
[18044.370542] ehci-pci 0000:00:02.1: GetStatus port:10 status 001005 0  ACK POWER sig=se0 PE CONNECT
[18044.423699] usb 1-10: new high-speed USB device number 19 using ehci-pci
[18044.477316] ehci-pci 0000:00:02.1: port 10 reset complete, port enabled
[18044.477321] ehci-pci 0000:00:02.1: GetStatus port:10 status 001005 0  ACK POWER sig=se0 PE CONNECT
[18044.568434] usb 1-10: skipped 1 descriptor after configuration
[18044.568437] usb 1-10: skipped 4 descriptors after interface
[18044.568675] usb 1-10: default language 0x0409
[18044.569426] usb 1-10: udev 19, busnum 1, minor = 18
[18044.569429] usb 1-10: New USB device found, idVendor=19d2, idProduct=1403
[18044.569431] usb 1-10: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[18044.569432] usb 1-10: Product: ZTE WCDMA Technologies MSM
[18044.569434] usb 1-10: Manufacturer: ZTE,Incorporated
[18044.569435] usb 1-10: SerialNumber: MF8230ZTED000000
[18044.569519] usb 1-10: usb_probe_device
[18044.569521] usb 1-10: configuration #1 chosen from 1 choice
[18044.586716] usb 1-10: adding 1-10:1.0 (config #1, interface 0)
[18044.587092] rndis_host 1-10:1.0: usb_probe_interface
[18044.587094] rndis_host 1-10:1.0: usb_probe_interface - got id
[18044.589314] rndis_host 1-10:1.0 usb0: register 'rndis_host' at usb-0000:00:02.1-10, RNDIS device, 36:4b:50:b7:ef:a2
[18044.589327] usb 1-10: adding 1-10:1.1 (config #1, interface 1)
[18044.589595] usb 1-10: adding 1-10:1.2 (config #1, interface 2)
[18044.589835] usb-storage 1-10:1.2: usb_probe_interface
[18044.589838] usb-storage 1-10:1.2: usb_probe_interface - got id
[18044.589841] usb-storage 1-10:1.2: USB Mass Storage device detected
[18044.589890] scsi17 : usb-storage 1-10:1.2
[17933.955215] systemd-udevd[21882]: renamed network interface usb0 to enp0s2f1u10
[18044.624011] systemd-udevd[22020]: renamed network interface usb0 to enp0s2f1u10
[18045.594327] scsi 17:0:0:0: Direct-Access     ZTE      MMC Storage      2.31 PQ: 0 ANSI: 2
[18045.594459] sd 17:0:0:0: Attached scsi generic sg2 type 0
[18045.596823] sd 17:0:0:0: [sdc] Attached SCSI removable disk

oraz ifconfig:

enp0s2f1u10: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.0.199  netmask 255.255.255.0  broadcast 192.168.0.255
        inet6 fe80::****:****:****:efa2  prefixlen 64  scopeid 0x20<link>
        ether 36:**:**:**:**:a2  txqueuelen 1000  (Ethernet)
        RX packets 398  bytes 134864 (131.7 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 466  bytes 152611 (149.0 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

Problem rozwiązany (Gargoyle + trzeba było doinstalować dodatkowe sterowniki). Najpóźniej jutro opiszę całą procedurę, może komuś się przyda :slight_smile:

To teraz informacje dot. instalacji (dzięki uwagom Cezarego z eko.one.pl):

Opis dla wersji Gargoyle z eko.one.pl
Najprościej: po prostu

opkg update
opkg install  kmod-usb-net-rndis

(Jednak router musi mieć połączenie z internetem)

Bez połączenia:

  1. Trzeba ściągnąć sterowniki kmod-usb-net-rndis odpowiedni dla konkretnej dystrybucji. Dla tej z eko.one.pl to będzie tutaj:
    http://dl.eko.one.pl/gargoyle-pl/attitude_adjustment/ar71xx/packages/
  2. Trzeba przenieść pliki z komputera na router. Ja użyłem do tego Uniksowej komenty scp, pewnie jest wiele sposobów
  3. Kiedy plik jest już na routerze:
    opkg install /sciezka_do_pliku/nazwa_pliku

Administratorze, bardzo dziękuję Ci za pomoc i czas. Pozdrawiam,
Michał

Dzięki za informacje w temacie, na pewno ktoś skorzysta z tego. Temat zamyka w razie problemów zapraszamy ponownie do nas na forum.