Router MR3220 nie rozpoznaje modemu MF 823

Instalacja i konfiguracja urządzeń TP-Link
#1

Witam,
jako, że podobny wątek został zamknięty, a nie rozwiązuje mojego problemu, zakładam zatem nowy.

  1. Ruter w wersji V2 najnowszy oryginalny firmware nie wykrywa modemu, komunikat "unplugged" Modem jest wykrywany przez komputer. Inny modem E3131 wersja Hi-link działa z tym routerem bez problemu.
  2. Po wgraniu do routera gargoyle-1.6.1.2-ar71xx-tl-mr3220-v2-squashfs-factory nie rozpoznaje obu modemów :o

W obu wariantach oba modemy sygnalizują diodą połączenie z internetem. Aktywnego huba nie posiadam, ale podłączałem też modem do osobnego zasilania i bez zmian.

Dodam jeszcze że MF823 jest w wersji rosyjskiej "Beeline". Czy to może być przyczyną problemów ?

#2

[quote="logen, post:1, topic:6303"]Dodam jeszcze że MF823 jest w wersji rosyjskiej "Beeline"[/quote] a dokładniej, jest brandowany?

#3

No, to jest właśnie taki ich "brand"


ale opisany jako ZTE MF823.

E3131 udało się uruchomić na Garygoyle'u ustawiając jako WAN DHCP(kablowe) i pomimo, że Modem 3G/4G pokazuje brak to połączenie jest. Natomiast MF823 na tych ustawianiach nie jest rozpoznawany choć dioda USB na modemie cały czas świeci.

#4

Uruchom router bez modemu, podłącz modem i wrzuć log na forum.

#5 
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.660000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.670000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.680000] console [ttyATH0] enabled, bootconsole disabled
Jan  1 01:00:39 Gargoyle kern.warn kernel: [    0.690000] m25p80 spi0.0: found en25q32b, expected m25p80
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.690000] m25p80 spi0.0: en25q32b (4096 Kbytes)
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.700000] 5 tp-link partitions found on MTD device spi0.0
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.700000] Creating 5 MTD partitions on "spi0.0":
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.710000] 0x000000000000-0x000000020000 : "u-boot"
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.720000] 0x000000020000-0x00000010971c : "kernel"
Jan  1 01:00:39 Gargoyle kern.warn kernel: [    0.720000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.730000] 0x00000010971c-0x0000003f0000 : "rootfs"
Jan  1 01:00:39 Gargoyle kern.warn kernel: [    0.740000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.750000] mtd: partition "rootfs" set to be root filesystem
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.760000] mtd: partition "rootfs_data" created automatically, ofs=3A0000, len=50000 
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.760000] 0x0000003a0000-0x0000003f0000 : "rootfs_data"
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.770000] 0x0000003f0000-0x000000400000 : "art"
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    0.780000] 0x000000020000-0x0000003f0000 : "firmware"
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.800000] ag71xx_mdio: probed
Jan  1 01:00:39 Gargoyle kern.info kernel: [    0.800000] eth0: Atheros AG71xx at 0xba000000, irq 5
Jan  1 01:00:39 Gargoyle kern.info kernel: [    1.360000] eth0: Found an AR7240/AR9330 built-in switch
Jan  1 01:00:39 Gargoyle kern.info kernel: [    2.390000] eth1: Atheros AG71xx at 0xb9000000, irq 4
Jan  1 01:00:39 Gargoyle kern.info kernel: [    2.940000] ag71xx ag71xx.0: eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
Jan  1 01:00:39 Gargoyle kern.info kernel: [    2.950000] TCP cubic registered
Jan  1 01:00:39 Gargoyle kern.info kernel: [    2.950000] NET: Registered protocol family 17
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    2.960000] Bridge firewalling registered
Jan  1 01:00:39 Gargoyle kern.info kernel: [    2.960000] Ebtables v2.0 registered
Jan  1 01:00:39 Gargoyle kern.info kernel: [    2.960000] 8021q: 802.1Q VLAN Support v1.8
Jan  1 01:00:39 Gargoyle kern.info kernel: [    2.970000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Jan  1 01:00:39 Gargoyle kern.info kernel: [    2.980000] Freeing unused kernel memory: 184k freed
Jan  1 01:00:39 Gargoyle kern.debug kernel: [    6.410000] Registered led device: tp-link:green:lan1
Jan  1 01:00:39 Gargoyle kern.debug kernel: [    6.410000] Registered led device: tp-link:green:lan2
Jan  1 01:00:39 Gargoyle kern.debug kernel: [    6.410000] Registered led device: tp-link:green:lan3
Jan  1 01:00:39 Gargoyle kern.debug kernel: [    6.410000] Registered led device: tp-link:green:lan4
Jan  1 01:00:39 Gargoyle kern.debug kernel: [    6.420000] Registered led device: tp-link:green:qss
Jan  1 01:00:39 Gargoyle kern.debug kernel: [    6.420000] Registered led device: tp-link:green:system
Jan  1 01:00:39 Gargoyle kern.debug kernel: [    6.420000] Registered led device: tp-link:green:wan
Jan  1 01:00:39 Gargoyle kern.debug kernel: [    6.420000] Registered led device: tp-link:green:wlan
Jan  1 01:00:39 Gargoyle kern.debug kernel: [    6.420000] Registered led device: tp-link:green:3g
Jan  1 01:00:39 Gargoyle kern.info kernel: [    7.360000] eth0: link up (1000Mbps/Full duplex)
Jan  1 01:00:39 Gargoyle kern.notice kernel: [    9.760000] JFFS2 notice: (445) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 34 of xref (0 dead, 17 orphan) found.
Jan  1 01:00:39 Gargoyle kern.notice kernel: [   10.500000] SCSI subsystem initialized
Jan  1 01:00:39 Gargoyle kern.info kernel: [   10.660000] usbcore: registered new interface driver usbfs
Jan  1 01:00:39 Gargoyle kern.info kernel: [   10.670000] usbcore: registered new interface driver hub
Jan  1 01:00:39 Gargoyle kern.info kernel: [   10.670000] usbcore: registered new device driver usb
Jan  1 01:00:39 Gargoyle kern.info kernel: [   11.140000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan  1 01:00:39 Gargoyle kern.info kernel: [   11.140000] ehci-platform ehci-platform: Generic Platform EHCI Controller
Jan  1 01:00:39 Gargoyle kern.info kernel: [   11.150000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
Jan  1 01:00:39 Gargoyle kern.info kernel: [   11.180000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
Jan  1 01:00:39 Gargoyle kern.info kernel: [   11.200000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Jan  1 01:00:39 Gargoyle kern.info kernel: [   11.200000] hub 1-0:1.0: USB hub found
Jan  1 01:00:39 Gargoyle kern.info kernel: [   11.200000] hub 1-0:1.0: 1 port detected
Jan  1 01:00:39 Gargoyle kern.info kernel: [   11.220000] Initializing USB Mass Storage driver...
Jan  1 01:00:39 Gargoyle kern.info kernel: [   11.230000] usbcore: registered new interface driver usb-storage
Jan  1 01:00:39 Gargoyle kern.info kernel: [   11.230000] USB Mass Storage support registered.
Jan  1 01:00:39 Gargoyle kern.info kernel: [   32.600000] eth0: link down
Jan  1 01:00:39 Gargoyle kern.info kernel: [   33.140000] Loading modules backported from Linux version master-2014-01-23-0-g62c147d
Jan  1 01:00:39 Gargoyle kern.info kernel: [   33.150000] Backport generated by backports.git backports-20140124-0-g1256d3e
Jan  1 01:00:39 Gargoyle kern.info kernel: [   33.330000] cfg80211: Calling CRDA to update world regulatory domain
Jan  1 01:00:39 Gargoyle kern.info kernel: [   33.330000] cfg80211: World regulatory domain updated:
Jan  1 01:00:39 Gargoyle kern.info kernel: [   33.340000] cfg80211:  DFS Master region: unset
Jan  1 01:00:40 Gargoyle kern.info kernel: [   33.340000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jan  1 01:00:40 Gargoyle kern.info kernel: [   33.350000] cfg80211:   (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:40 Gargoyle kern.info kernel: [   33.360000] cfg80211:   (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:40 Gargoyle kern.debug kernel: [   34.460000] ath: EEPROM regdomain: 0x0
Jan  1 01:00:40 Gargoyle kern.debug kernel: [   34.460000] ath: EEPROM indicates default country code should be used
Jan  1 01:00:40 Gargoyle kern.debug kernel: [   34.460000] ath: doing EEPROM country->regdmn map search
Jan  1 01:00:40 Gargoyle kern.debug kernel: [   34.460000] ath: country maps to regdmn code: 0x3a
Jan  1 01:00:40 Gargoyle kern.debug kernel: [   34.460000] ath: Country alpha2 being used: US
Jan  1 01:00:40 Gargoyle kern.debug kernel: [   34.460000] ath: Regpair used: 0x3a
Jan  1 01:00:40 Gargoyle kern.debug kernel: [   34.480000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Jan  1 01:00:40 Gargoyle kern.debug kernel: [   34.480000] Registered led device: ath9k-phy0
Jan  1 01:00:40 Gargoyle kern.info kernel: [   34.480000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
Jan  1 01:00:40 Gargoyle kern.info kernel: [   34.500000] cfg80211: Calling CRDA for country: US
Jan  1 01:00:40 Gargoyle kern.info kernel: [   34.500000] cfg80211: Regulatory domain changed to country: US
Jan  1 01:00:40 Gargoyle kern.info kernel: [   34.500000] cfg80211:  DFS Master region: unset
Jan  1 01:00:40 Gargoyle kern.info kernel: [   34.510000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jan  1 01:00:40 Gargoyle kern.info kernel: [   34.520000] cfg80211:   (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:40 Gargoyle kern.info kernel: [   34.520000] cfg80211:   (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:40 Gargoyle kern.info kernel: [   34.750000] PPP generic driver version 2.4.2
Jan  1 01:00:40 Gargoyle kern.info kernel: [   34.900000] ip_tables: (C) 2000-2006 Netfilter Core Team
Jan  1 01:00:40 Gargoyle kern.info kernel: [   35.330000] NET: Registered protocol family 24
Jan  1 01:00:40 Gargoyle kern.info kernel: [   35.390000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
Jan  1 01:00:40 Gargoyle kern.info kernel: [   36.040000] xt_time: kernel timezone is -0000
Jan  1 01:00:40 Gargoyle kern.info kernel: [   36.760000] 	Hooked IMQ after mangle on PREROUTING
Jan  1 01:00:40 Gargoyle kern.info kernel: [   36.770000] 	Hooked IMQ after nat on POSTROUTING
Jan  1 01:00:40 Gargoyle kern.info kernel: [   36.770000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
Jan  1 01:00:40 Gargoyle kern.info kernel: [   36.980000] Netfilter messages via NETLINK v0.30.
Jan  1 01:00:40 Gargoyle kern.notice kernel: [   37.040000] ip_set: protocol 6
Jan  1 01:00:40 Gargoyle kern.info kernel: [   37.630000] usbcore: registered new interface driver cdc_acm
Jan  1 01:00:40 Gargoyle kern.info kernel: [   37.630000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Jan  1 01:00:40 Gargoyle kern.info kernel: [   37.770000] usbcore: registered new interface driver usbserial
Jan  1 01:00:40 Gargoyle kern.info kernel: [   37.780000] USB Serial support registered for generic
Jan  1 01:00:40 Gargoyle kern.info kernel: [   37.780000] usbcore: registered new interface driver usbserial_generic
Jan  1 01:00:40 Gargoyle kern.info kernel: [   37.790000] usbserial: USB Serial Driver core
Jan  1 01:00:40 Gargoyle kern.info kernel: [   37.840000] usbcore: registered new interface driver cdc_ether
Jan  1 01:00:40 Gargoyle kern.info kernel: [   37.980000] usbcore: registered new interface driver cdc_ncm
Jan  1 01:00:40 Gargoyle kern.info kernel: [   38.090000] USB Serial support registered for GSM modem (1-port)
Jan  1 01:00:40 Gargoyle kern.info kernel: [   38.100000] usbcore: registered new interface driver option
Jan  1 01:00:40 Gargoyle kern.info kernel: [   38.100000] option: v0.7.2:USB Driver for GSM modems
Jan  1 01:00:40 Gargoyle kern.info kernel: [   38.230000] USB Serial support registered for Sierra USB modem
Jan  1 01:00:40 Gargoyle kern.info kernel: [   38.230000] usbcore: registered new interface driver sierra
Jan  1 01:00:40 Gargoyle kern.info kernel: [   38.240000] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
Jan  1 01:00:42 Gargoyle user.notice usb-modeswitch: 1-0:1.0: Manufacturer=Linux_3.3.8_ehci_hcd Product=Generic_Platform_EHCI_Controller Serial=ehci-platform
Jan  1 01:00:46 Gargoyle kern.info kernel: [   46.050000] eth0: link up (1000Mbps/Full duplex)
Jan  1 01:00:46 Gargoyle kern.info kernel: [   46.670000] eth0: link down
Jan  1 01:00:47 Gargoyle daemon.notice netifd: Interface 'lan' is now up
Jan  1 01:00:47 Gargoyle kern.info kernel: [   47.700000] device eth0 entered promiscuous mode
Jan  1 01:00:47 Gargoyle daemon.notice netifd: Interface 'loopback' is now up
Jan  1 01:00:48 Gargoyle user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Jan  1 01:00:48 Gargoyle daemon.notice netifd: wan (1013): udhcpc (v1.19.4) started
Jan  1 01:00:48 Gargoyle daemon.notice netifd: wan (1013): Sending discover...
Jan  1 01:00:48 Gargoyle kern.info kernel: [   48.800000] eth0: link up (1000Mbps/Full duplex)
Jan  1 01:00:48 Gargoyle kern.info kernel: [   48.800000] br-lan: port 1(eth0) entered forwarding state
Jan  1 01:00:48 Gargoyle kern.info kernel: [   48.810000] br-lan: port 1(eth0) entered forwarding state
Jan  1 01:00:50 Gargoyle kern.info kernel: [   50.810000] br-lan: port 1(eth0) entered forwarding state
Jan  1 01:00:51 Gargoyle daemon.notice netifd: wan (1013): Sending discover...
Jan  1 01:00:52 Gargoyle kern.info kernel: [   52.620000] device wlan0 entered promiscuous mode
Jan  1 01:00:52 Gargoyle kern.info kernel: [   52.970000] br-lan: port 2(wlan0) entered forwarding state
Jan  1 01:00:52 Gargoyle kern.info kernel: [   52.980000] br-lan: port 2(wlan0) entered forwarding state
Jan  1 01:00:54 Gargoyle daemon.notice netifd: wan (1013): Sending discover...
Jan  1 01:00:54 Gargoyle kern.info kernel: [   54.980000] br-lan: port 2(wlan0) entered forwarding state
Jan  1 12:00:02 Gargoyle authpriv.info dropbear[1483]: Running in background
Jan  1 12:00:02 Gargoyle daemon.warn httpd_gargoyle[1508]: started as root without requesting chroot(), warning only
Jan  1 12:00:02 Gargoyle daemon.notice httpd_gargoyle[1508]: httpd_gargoyle/1.0 14mar2008 starting on Gargoyle, port 80
Jan  1 12:00:03 Gargoyle user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Jan  1 12:00:03 Gargoyle user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Jan  1 12:00:03 Gargoyle user.notice dnsmasq: Allowing RFC1918 responses for domain free.aero2.net.pl
Jan  1 12:00:03 Gargoyle daemon.info dnsmasq[1534]: started, version 2.66 cachesize 150
Jan  1 12:00:03 Gargoyle daemon.info dnsmasq[1534]: compile time options: no-IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth
Jan  1 12:00:03 Gargoyle daemon.info dnsmasq[1534]: using local addresses only for domain lan
Jan  1 12:00:03 Gargoyle daemon.info dnsmasq[1534]: reading /tmp/resolv.conf.auto
Jan  1 12:00:03 Gargoyle daemon.warn dnsmasq[1534]: ignoring nameserver 192.168.1.1 - local interface
Jan  1 12:00:03 Gargoyle daemon.info dnsmasq[1534]: using local addresses only for domain lan
Jan  1 12:00:03 Gargoyle daemon.info dnsmasq[1534]: read /etc/hosts - 2 addresses
Jan  1 12:00:04 Gargoyle user.info sysinit: ERROR: No valid dynamic DNS service configurations defined
Jan  1 12:00:04 Gargoyle user.info sysinit: (Did you specify correct configuration file path?)
Jan  1 12:00:04 Gargoyle user.info sysinit: setting up led WAN
Jan  1 12:00:04 Gargoyle user.info sysinit: setting up led LAN1
Jan  1 12:00:04 Gargoyle user.info sysinit: setting up led LAN2
Jan  1 12:00:04 Gargoyle user.info sysinit: setting up led LAN3
Jan  1 12:00:04 Gargoyle user.info sysinit: setting up led LAN4
Jan  1 12:00:04 Gargoyle user.info sysinit: setting up led WLAN
Jan  1 12:00:04 Gargoyle user.info sysinit: setting up led USB
Jan  1 12:00:57 Gargoyle kern.info kernel: [  112.070000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Jan  1 12:00:57 Gargoyle kern.info kernel: [  112.280000] scsi0 : usb-storage 1-1:1.0
Jan  1 12:00:57 Gargoyle user.notice usb-modeswitch: 1-1:1.0: Manufacturer=ZTE,Incorporated Product=ZTE_WCDMA_Technologies_MSM Serial=MF8230ZTED010000
Jan  1 12:00:57 Gargoyle user.notice usb-modeswitch: 1-1:1.0: Selecting /etc/usb_modeswitch.d/19d2:1225 for mode switching
Jan  1 12:00:58 Gargoyle syslog.notice usb_modeswitch: switch device 19d2:1225 on 001/002
Jan  1 12:00:58 Gargoyle kern.warn kernel: [  112.760000] usb 1-1: usbfs: process 1793 (usb_modeswitch) did not claim interface 0 before use
Jan  1 12:01:03 Gargoyle kern.info kernel: [  117.790000] usb 1-1: USB disconnect, device number 2
Jan  1 12:01:03 Gargoyle kern.info kernel: [  118.230000] usb 1-1: new high-speed USB device number 3 using ehci-platform
Jan  1 12:01:03 Gargoyle kern.info kernel: [  118.420000] scsi1 : usb-storage 1-1:1.2
Jan  1 12:01:04 Gargoyle kern.notice kernel: [  119.420000] scsi 1:0:0:0: CD-ROM            CWID     USB SCSI CD-ROM  2.31 PQ: 0 ANSI: 2
Jan  1 12:01:04 Gargoyle kern.notice kernel: [  119.420000] scsi 1:0:0:1: Direct-Access     ZTE      MMC Storage      2.31 PQ: 0 ANSI: 2
Jan  1 12:01:04 Gargoyle kern.notice kernel: [  119.440000] sd 1:0:0:1: [sda] Attached SCSI removable disk
Success

Dodam jeszcze, że router na oryginalnym firmware rozpoznawał ten modem, ale tylko bez karty SIM ??? Był komunikat, że zidentyfikowano i połączono. Można było zalogować się na 192.168.0.1. Oczywiście strona niekompletna bez SIM.
Czy można ten modem sflaszować na inny brand, np. PLAY ?

#6

Zaloguj się przez putty i podaj wyniki z poleceń:

cat /proc/bus/usb/devices
ifconfig -a
cat /etc/config/network
#7 
 ----------------------------------------------------------------
 | Machine: TP-Link TL-MR3220 v2                                |
 | Uptime: 0d, 00:31:30                                         |
 | Load: 0.00 0.01 0.05                                         |
 | Flash: total: 320KB, free: 80KB, used: 75%                   |
 | Memory: total: 28.5MB, free: 16.0MB, used: 43%               |
 | WAN:                                                         |
 | LAN: 192.168.1.1                                             |
 | WLAN: mode: ap, ssid: Gargoyle, channel: 11, conn: 0         |
 ----------------------------------------------------------------
root@Gargoyle:~# cat /proc/bus/usb/devices
T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480  MxCh= 1
B:  Alloc=  0/800 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev= 3.03
S:  Manufacturer=Linux 3.3.8 ehci_hcd
S:  Product=Generic Platform EHCI Controller
S:  SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=02(comm.) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=19d2 ProdID=1405 Rev=f0.ab
S:  Manufacturer=ZTE,Incorporated
S:  Product=ZTE WCDMA Technologies MSM
S:  SerialNumber=MF8230ZTED010000
C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E:  Ad=82(I) Atr=03(Int.) MxPS=  16 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
root@Gargoyle:~# ifconfig -a
br-lan    Link encap:Ethernet  HWaddr A0:F3:C1:7B:DB:BF
          inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:2631 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1676 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:217114 (212.0 KiB)  TX bytes:257589 (251.5 KiB)
eth0      Link encap:Ethernet  HWaddr A0:F3:C1:7B:DB:BF
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:2648 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1677 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:255518 (249.5 KiB)  TX bytes:257631 (251.5 KiB)
          Interrupt:5
eth1      Link encap:Ethernet  HWaddr A0:F3:C1:7B:DB:C1
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:4
imq0      Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00                                                                              -00
          NOARP  MTU:16000  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:11000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
imq1      Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00                                                                              -00
          NOARP  MTU:16000  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:11000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:7680 errors:0 dropped:0 overruns:0 frame:0
          TX packets:7680 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:461136 (450.3 KiB)  TX bytes:461136 (450.3 KiB)
usb0      Link encap:Ethernet  HWaddr 36:4B:50:B7:EF:6B
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
wlan0     Link encap:Ethernet  HWaddr A0:F3:C1:7B:DB:C0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1021 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:112084 (109.4 KiB)
root@Gargoyle:~# cat /etc/config/network
config interface 'loopback'
        option ifname 'lo'
        option proto 'static'
        option ipaddr '127.0.0.1'
        option netmask '255.0.0.0'
config interface 'lan'
        option ifname 'eth0'
        option type 'bridge'
        option proto 'static'
        option ipaddr '192.168.1.1'
        option netmask '255.255.255.0'
        option dns '192.168.1.1'
config interface 'wan'
        option ifname 'eth1'
        option proto 'dhcp'
config switch
        option name 'eth0'
        option reset '1'
        option enable_vlan '1'
config switch_vlan
        option device 'eth0'
        option vlan '1'
        option ports '0 1 2 3 4'
#8

Wg tego modem zachowuje się poprawnie.
W konfiguracji gargoyle zmień:
Połączenie - DHCP (kablowe)
Interfejs WAN - usb0
Adres IP urządzenia - 192.168.0.1 (po zapisaniu to będzie adres do konfiguracji routera).
Reszta wg siebie. Zapisać zmiany.

#9

No tak, teraz rzeczywiście jest opcja WAN - usb0 i można się zalogować na router, ale wszystkie te operacje robiłem bez karty SIM. Po jej włożeniu jest tylko interfejs WAN - Domyślny i brak komunikacji z modemem. Jeszcze raz powtórzyć poprzednie polecenia ?

#10

Wrzuć jeszcze raz to samo z włożoną kartą sim. Log z routera tez wrzuć.

#11

Po włożeniu karty SIM dzieje się coś dziwnego, bo LED USB zapala się a potem gaśnie co zresztą widać w logach.

Jan  1 12:03:28 Gargoyle kern.info kernel: [  262.620000] usb 1-1: new high-speed USB device number 4 using ehci-platform
Jan  1 12:03:28 Gargoyle kern.info kernel: [  262.820000] scsi1 : usb-storage 1-1:1.2
Jan  1 12:03:29 Gargoyle kern.notice kernel: [  263.820000] scsi 1:0:0:0: CD-ROM            CWID     USB SCSI CD-ROM  2.31 PQ: 0 ANSI: 2
Jan  1 12:03:29 Gargoyle kern.notice kernel: [  263.830000] scsi 1:0:0:1: Direct-Access     ZTE      MMC Storage      2.31 PQ: 0 ANSI: 2
Jan  1 12:03:29 Gargoyle kern.notice kernel: [  263.850000] sd 1:0:0:1: [sda] Attached SCSI removable disk
Jan  1 12:03:53 Gargoyle user.notice usb-modeswitch: 1-1:1.0: Manufacturer=ZTE,Incorporated Product=ZTE_WCDMA_Technologies_MSM Serial=MF8230ZTED010000
Jan  1 12:03:53 Gargoyle user.notice usb-modeswitch: 1-1:1.1: Manufacturer=ZTE,Incorporated Product=ZTE_WCDMA_Technologies_MSM Serial=MF8230ZTED010000
Jan  1 12:03:53 Gargoyle user.notice usb-modeswitch: 1-1:1.2: Manufacturer=ZTE,Incorporated Product=ZTE_WCDMA_Technologies_MSM Serial=MF8230ZTED010000
Jan  1 12:03:56 Gargoyle kern.info kernel: [  291.240000] usb 1-1: USB disconnect, device number 4
Jan  1 12:03:57 Gargoyle kern.info kernel: [  291.530000] usb 1-1: new high-speed USB device number 5 using ehci-platform
Jan  1 12:03:57 Gargoyle kern.err kernel: [  291.690000] hub 1-0:1.0: unable to enumerate USB device on port 1

Putty zrobię za chwilkę...

#12

Reszty nie trzeba.. Zbyt słaby router żeby zasilić modem. Użyj aktywnego HUBa USB.

#13

Hub podłączony. Chyba jest lepiej, ale nadal nie mogę wbić się na router.

    Jan  1 01:06:54 Gargoyle kern.info kernel: [  168.260000] hub 1-1:1.0: USB hub found
    Jan  1 01:06:54 Gargoyle kern.info kernel: [  168.260000] hub 1-1:1.0: 4 ports detected
    Jan  1 01:06:55 Gargoyle user.notice usb-modeswitch: 1-1:1.0: Manufacturer=? Product=USB2.0_Hub Serial=?
    Jan  1 01:06:55 Gargoyle kern.info kernel: [  168.560000] usb 1-1.4: new high-speed USB device number 5 using ehci-platform
    Jan  1 01:06:55 Gargoyle kern.info kernel: [  168.730000] scsi1 : usb-storage 1-1.4:1.2
    Jan  1 01:06:55 Gargoyle user.notice usb-modeswitch: 1-1.4:1.0: Manufacturer=ZTE,Incorporated Product=ZTE_WCDMA_Technologies_MSM Serial=MF8230ZTED010000
    Jan  1 01:06:55 Gargoyle user.notice usb-modeswitch: 1-1.4:1.1: Manufacturer=ZTE,Incorporated Product=ZTE_WCDMA_Technologies_MSM Serial=MF8230ZTED010000
    Jan  1 01:06:55 Gargoyle user.notice usb-modeswitch: 1-1.4:1.2: Manufacturer=ZTE,Incorporated Product=ZTE_WCDMA_Technologies_MSM Serial=MF8230ZTED010000
    Jan  1 01:06:56 Gargoyle kern.notice kernel: [  169.730000] scsi 1:0:0:0: CD-ROM            CWID     USB SCSI CD-ROM  2.31 PQ: 0 ANSI: 2
    Jan  1 01:06:56 Gargoyle kern.notice kernel: [  169.740000] scsi 1:0:0:1: Direct-Access     ZTE      MMC Storage      2.31 PQ: 0 ANSI: 2
    Jan  1 01:06:56 Gargoyle kern.notice kernel: [  169.750000] sd 1:0:0:1: [sda] Attached SCSI removable disk
    Jan  1 01:07:26 Gargoyle kern.info kernel: [  199.540000] usb 1-1.4: USB disconnect, device number 5
    Jan  1 01:07:47 Gargoyle kern.info kernel: [  221.030000] usb 1-1.1: new high-speed USB device number 6 using ehci-platform
    Jan  1 01:07:47 Gargoyle kern.info kernel: [  221.190000] scsi2 : usb-storage 1-1.1:1.0
    Jan  1 01:07:47 Gargoyle user.notice usb-modeswitch: 1-1.1:1.0: Manufacturer=ZTE,Incorporated Product=ZTE_WCDMA_Technologies_MSM Serial=MF8230ZTED010000
    Jan  1 01:07:47 Gargoyle user.notice usb-modeswitch: 1-1.1:1.0: Selecting /etc/usb_modeswitch.d/19d2:1225 for mode switching
    Jan  1 01:07:48 Gargoyle syslog.notice usb_modeswitch: switch device 19d2:1225 on 001/006
    Jan  1 01:07:48 Gargoyle kern.warn kernel: [  221.730000] usb 1-1.1: usbfs: process 2334 (usb_modeswitch) did not claim interface 0 before use
    Jan  1 01:07:53 Gargoyle kern.info kernel: [  226.930000] usb 1-1.1: USB disconnect, device number 6
    Jan  1 01:07:53 Gargoyle kern.info kernel: [  227.220000] usb 1-1.1: new high-speed USB device number 7 using ehci-platform
    Jan  1 01:07:53 Gargoyle kern.info kernel: [  227.370000] scsi3 : usb-storage 1-1.1:1.2
    Jan  1 01:07:54 Gargoyle kern.notice kernel: [  228.370000] scsi 3:0:0:0: CD-ROM            CWID     USB SCSI CD-ROM  2.31 PQ: 0 ANSI: 2
    Jan  1 01:07:54 Gargoyle kern.notice kernel: [  228.370000] scsi 3:0:0:1: Direct-Access     ZTE      MMC Storage      2.31 PQ: 0 ANSI: 2
    Jan  1 01:07:54 Gargoyle kern.notice kernel: [  228.390000] sd 3:0:0:1: [sda] Attached SCSI removable disk
    Jan  1 01:08:19 Gargoyle user.notice usb-modeswitch: 1-1.1:1.0: Manufacturer=ZTE,Incorporated Product=ZTE_WCDMA_Technologies_MSM Serial=MF8230ZTED010000
    Jan  1 01:08:19 Gargoyle user.notice usb-modeswitch: 1-1.1:1.1: Manufacturer=ZTE,Incorporated Product=ZTE_WCDMA_Technologies_MSM Serial=MF8230ZTED010000
    Jan  1 01:08:19 Gargoyle user.notice usb-modeswitch: 1-1.1:1.2: Manufacturer=ZTE,Incorporated Product=ZTE_WCDMA_Technologies_MSM Serial=MF8230ZTED010000
    Success
#14

To ustawiłeś?

Jak tak to daj jeszcze:

#15

Nie ma takiej możliwości WAN-usb0. Jest tylko WAN-Domyślnie co nic nie daje. Może jednak ten router nie wspiera takiego klona MF823 ? Zrobić jednak Putty ?

#16

Tak

#17 
root@Gargoyle:~# cat /proc/bus/usb/devices
T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480  MxCh= 1
B:  Alloc=  0/800 us ( 0%), #Int=  1, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev= 3.03
S:  Manufacturer=Linux 3.3.8 ehci_hcd
S:  Product=Generic Platform EHCI Controller
S:  SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  4 Spd=480  MxCh= 4
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=05e3 ProdID=0608 Rev= 9.01
S:  Product=USB2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=256ms
T:  Bus=01 Lev=02 Prnt=04 Port=00 Cnt=01 Dev#=  7 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=19d2 ProdID=1403 Rev=f0.ab
S:  Manufacturer=ZTE,Incorporated
S:  Product=ZTE WCDMA Technologies MSM
S:  SerialNumber=MF8230ZTED010000
C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=03
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=ff Driver=(none)
E:  Ad=82(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
root@Gargoyle:~# cat /etc/config/network
config interface 'loopback'
        option ifname 'lo'
        option proto 'static'
        option ipaddr '127.0.0.1'
        option netmask '255.0.0.0'
config interface 'lan'
        option ifname 'eth0'
        option type 'bridge'
        option proto 'static'
        option ipaddr '192.168.1.1'
        option netmask '255.255.255.0'
config interface 'wan'
        option ifname 'eth1'
        option proto 'dhcp'
config switch
        option name 'eth0'
        option reset '1'
        option enable_vlan '1'
config switch_vlan
        option device 'eth0'
        option vlan '1'
        option ports '0 1 2 3 4'
#18

Dziwna sprawa. Modem źle się przełącza. Jego dane to "P: Vendor=19d2 ProdID=1403 Rev=f0.ab" a powinno być "P: Vendor=19d2 ProdID=1405 Rev=f0.ab
Spróbuj zmienić adres IP urządzenia na 192.168.1.1
Daj potem wynik komendy: ifconfig -a

#19

Sporo mi już pomogłeś, ale sorry trochę się już w tym gubię. Nie jestem z resztą informatykiem.
IP=192.168.1.1 mam ustawić na modemie czy bramkę na routerze ? Ta komenda co podałeś to przez Putty ? Może ten hub tutaj coś knoci ?

#20

W routerze. Konfiguracja - podstawowa.

Komenda przez putty. Hub widać zasila poprawnie.
Modem bez karty jest prawidłowo przełączony, z kartą nie potrafi się przełączyć w odpowiedni tryb.